STC15series MCU
1、芯片的描述:
STC15F2K60S2 series MCU is a single-chip microcontroller based on a high performance IT architecture 8051 CPU. which is produced by STC MCU Limited. It is a new generation of 8051 MCU of high speed, high stability, low power consumption and super strong anti-disturbance(点击即可咨询芯片详细信息). Besides, STC15E2K60S2 series MCU is a MCU of super advanced encryption, because it adopts the eighth generation of STC encryption technology. With the enhanced kernel, STC15F2K60S2 series MCU is faster than a traditional 8051 in executing instructions (about 8-12 times the rate of a traditional 8051 MCU), and has a fully compatible instruction set with traditional 8051 series microcontroller. External expensive crystal can be removed by being integrated internal high-precise R/C clock(±0.3%) with ±1% temperature drift (-40℃-+85℃) while ±0.6% in normal temperature (-20℃~+65℃) and wide frenquency adjustable between 5MHz and 35MHz. External reset curcuit also can be removed by being integrated internal highly reliable one with 8 levels optional threshold voltage of reset. The STC15F2K60S2 series MCU retains all features of the traditional 8051. In addition, it has 3-channels CCP/PCA/PWM, 8-channels and 10-bits A/D Converter(300 thousand times per sec.), large capacity of 2K bytes SRAM, two high-speed asynchronous serial ports--UARTs(UARTI/UART2. can be regarded as 5 serial ports by shifting among 5 groups of pins) and a high-speed synchronous serial peripheral interface----PI. STC15F2K60S2 series MCU is usually used in communications which need for serveral UARTs or electrical control or some occasion with strong disturbance
2、芯片特性:
① The Programmable clock output of TO is on P3.5/TOCLKO (output by dividing the frequency of the internal system clock or the input clock of external pin TO/P3.4)②) The Programmable clock output of TI is on P3.4/TICLKO (output by dividing the frequency of the internal system clock or the input clock of external pin T1/P3.5)③) The Programmable clock output of T2 is on P3.0/T2CLKO (output by dividing the frequency of the internal system clock or the input clock of external pin T2/P3.1)Three timers/counters in above all can be output by dividing the frequency from 1 to 65536④) The Programmable clock output of master clock is on P5.4/MCLKO, and its frequency can be divided into MCLK/1, MCLK/2. MCLK/4. The master clock can either be internal R/C clock or the external input clock or the external crystal oscillator. MCLK is the frequency of master clock. MCLKO is the output of master clock. It is on MCLKO/P3.4 that the Programmable clock output of master clock of STC15 series 8-pin MCU (such as STC15F101 W series).However, it is on MCLKO/P5.4 that the Programmable clock output of master clock of other STC15 series MCU including 16-pin or more than 16-pin MCU(such as STC15F2K60S2. STC15W4K32S4 and so on)One 15 bits Watch-Dog-Timer with 8-bit pre-scaler (one-time-enabled)advanced instruction set, which is fully compatible with traditional 8051 MCU. have hardware multiplication / division command. 42/38/30/26 common I/O ports are available, their mode is quasi bidirectional/weak pull-up (traditional 80S1 IO ports mode) after reset, and can be set to four modes: quasi bidirectional/weak pull-up, strong push-pull strong pull-up, input-only/high-impedance and open drain. the driving ability of each I/O port can be up to 20mA, but it don't exceed this maximum 120mA that the current of the whole chip of 40-pin or more than 40-pin MCU, while 90mA that the current of the whole chip of 16-pin or more than 16-pin MCU or 32-pin or less than 32-pin MCU. If I/O ports are not enough, it can be extended by connecting a 74HC595(reference price: RMB 0.15 yuan). Besides, cascading several chips also can extend to dozens of I/O ports. Package: LOFP44 (12mm x 12mm), LOFP-32 (9mm x 9mm), TSSOP20(6.5mm x 6.5mm), SOP28, SKDIP28. PDIP-40
3、典型线路图:
4、封装(脚位)
5、订购信息:
桑尼奇科技是深圳市知名的IC代理商,能为广大工程师与采购朋友提供众多类型产品,小批量当天交货,10K以上5-10天交货。